How to ride the mechanics ?

How to ride the mechanics ?

Some novice drivers may seem that learning to drive a car with a manual transmission is impossible.However, it is not so.For many professional drivers automatic transmission seems quite acceptable, and they would never trade her mechanics.The ability to cope with manual transmission - is the foundation of driving skills.In order to ease the driving training on cars with manual transmission is to figure out how to ride on the mechanics.

How to shift gears on the mechanics

Of course, before you sit behind the wheel of a car with a manual transmission, you need to find out what it is and how to shift gears in the manual transmission.First, we should explain how the transmission.The crank shaft of the engine not directly transmits the motion to the wheels through a certain number of devices, including clutch and gearbox mechanism.It has several different sized gears.They allow the engine to run optimally for him.When done squeezing the clutch pedal, the clutch starts connector, causing the gears in the gearbox (with gear change) smoothly into the next drive mode.All beginners interested in learning how to ride on the mechanics, and in fact should first examine the inclusion of transmission scheme and learn them fast and easy to switch.This is best practice unwound sat behind the wheel of the car.Each driver must ensure synchronicity of their movements, squeezing the gas pedal and dropping the clutch pedal.Keep in mind that if abruptly release the clutch pedal, the car jerked, or stall, and this in turn in city driving can cause a lot of unpleasant moments.Therefore, the elaboration of the moment should be given special attention.

How to drive mechanics

So, you sat behind the wheel of a car, there is a question that needs to be done to pull away?To do this, you must check whether the neutral speed is enabled, then start the car, then squeeze the clutch and engage first gear.If you need to go back, then reverse.We must now start to increase engine speed, it needs to smoothly and slowly begin to let go of the clutch without jerks.At some point, the vehicle begins to move at the same time the engine speed will drop.To this point the machine is not stalled, it is necessary to hold the gas pedal a little, and then increase engine speed, fully release the clutch.Experienced drivers perform all these actions clearly and quickly, and the novice can hold long enough for the clutch pedal depressed, which in turn has a negative impact on the term "life" of the clutch.

Gear shifting on the go

necessary torque gear should be selected, depending on the vehicle speed and engine speed.Typically, the first operating speed in a range from 0 to 20, 20 to the second 40, third 40 to 60, the fourth 60 and the fifth over 90 km / h.When it was time to increase the speed, it is necessary to shift gears in motion.This is done as follows: After reaching 3000-4000 rpm motor, it is necessary to include the second gear.To do so, let the gas pedal while simultaneously pressing the clutch.At first, it may cause some problems, but gradually develop into a skill.Then, while the vehicle is moving coasting forward and the clutch is fully depressed, the lever must be switched to the second speed.After that you should release the clutch smoothly to the end and add gas.It should be noted that each vehicle has its own optimal speed switching time to a higher gear.This time depends on the engine capacity and from the transmission settings.To facilitate the work of the brake system, and increase the stability of the rear-wheel drive cars in conditions of ice will help braking by the engine.In this case, you need to let go of the gas pedal, and after a significant reduction in engine speed to squeeze the grip, and then quickly switch to a lower gear.

Parking

Talking about how to ride on the mechanics, it is impossible not to touch upon the issue of parking.During parking between cars newcomer is best to hold the clutch pedal and drive up to the barrier at a very low speed.All this will, if necessary, quickly squeeze it thoroughly and apply the brakes to avoid a collision with a neighboring car.Keep in mind, you can even squeeze the brake without pressing the clutch, it will help to save time in an emergency situation, despite the fact that the machine stops.Although it is not entirely correct, but it is better then to repair the clutch, than someone else's car.

Handbrake

This detail is very important when driving on the manual transmission.Indeed, in contrast to the machine, when pulling downhill, mechanics can begin to roll back.In this situation, you will save a manual brake.Stopping at traffic lights or before switching, which is on the rise, set the car on the handbrake and the gear shift in neutral.When it's time to get under way, depress the clutch, engage first gear, slowly release the clutch and slowly press on the gas, when you feel that the clutch discs begin to connect smoothly release the handbrake.

Hopefully this article has helped you understand how to ride the mechanics.